I went to a large truck parts store and they had these K-Tool International KTI-55123. K-Tool International KTI-55123 Straight Tip Snap-Ring Pliers The requirements are quite strict because the Ford snap ring pliers must be heavy duty hardened steel to not bend or break while spreading the hefty retaining clips Ford used, but they must also be long enough to reach inside the hub while also being skinny enough to spread the snap ring without hitting the sides of the hub. Here’s a run-down of the snap ring pliers suggested by Ford owners. Best Snap Ring Pliers for F250 Hub Forum Suggestions Normally I’d go for something USA made, but I’m not going to let a tool’s country of origin stop me from getting the best possible tool for the job. KNIPEX is THE authority on snap-ring pliers, and they are still cheaper than some of the other tools listed with inflated prices. 094″ tip size coupled with the 9 inches of length for reaching into Ford hubs. My personal suggestion would be the KNIPEX Tools 4911A3 External Straight Retaining Ring 9in Pliers because of the. KNIPEX is a German company and its tools are very high quality, I especially like the slight outward offset the tips have for grabbing onto the snap ring and not letting it slide off while being spread. It’s easy to see from the table that the Knipex 11A series of snap ring pliers are a good balance of productivity and affordability when it comes to removing the snap ring pliers on ford Super Duty F-250, F-350, and F-450 pickup trucks, as well as the Ford Excursion. Tool LinkĤ611A3 External Straight Retaining Ring PliersĤ611A2 External Straight Retaining Ring PliersĤ911A3 External Straight Retaining Ring PliersĤ611A4 External Straight Retaining Ring Pliers Table of Best Snap Ring Pliers for F250 HubsĬlick column headers to sort columns – Tool Link column contains affiliate links that may earn me a commission. Actual suggestions from people working on their Ford Super Duty hubs can be found under the table. I decided to remedy this problem by compiling all the suggested snap ring pliers into a single list with a comparison table. I figured so many Ford F250, F350, and F450 owners in forums ask for help finding good Snap-Ring Pliers for their wheel hubs because there aren’t any definitive results on Google when searching “best snap ring pliers for f250 hub” aside from message board and forum results, many of which are quite outdated and have broken images. The Ford Excursion uses the same chassis as Super duty pickups so it naturally uses the same hubs as well. The wheel hub assemblies on 2005 and newer Ford Super Duties are held onto the axle with a heavy duty retaining clips that most snap ring pliers either can’t reach or are too flimsy to spread. I think I’ve set about 4 snap rings this year….One of the things I see people asking for help with the most in Ford forums is which snap-ring pliers are best for for the snap-rings (retaining clips) that keep wheel hubs attached on F-250s and other Super Duty trucks, plus Ford Excursions. Handtools of the greatest generation!ĮDIT: In fairness, and my rant notwithstanding, if I needed a set of snap-ring tools, that HF set would most likely be just fine. He took them with him when he left the Navy….in 1946! American made, tough as nails, still going strong since WWII. For $5.99/bx of 100, nobody can beat that….įWIW, my snap-ring pliers were my dad’s. When I was a commercial diver, we used HF handtools all the time……and considered them "disposable", routinely leaving them on the ocean floor when the job was done.Ībout the only thing that I always / only buy from HF are Nitrile gloves. Otherwise, it’s usually Snap-On or Mac for me. If there’s a backwards-left-handed-stubby-offset wrench that I must have but will only use once a year, I’ll go to HF. On sale at HF for $2 ea., it was impossible to say "no", especially when I knew I’d break some, I’d slather them in epoxy, and virtually destroy them eventually one way or another.īut, yeah, I get it: cheap tools are not worth it. I built my boat and needed about 75 bar clamps.
0 Comments
Leave a Reply. |
AuthorWrite something about yourself. No need to be fancy, just an overview. ArchivesCategories |